- 您现在的位置：买卖IC网 > Sheet目录346 > NCP5623BMUTBG (ON Semiconductor)IC LED DRIVER RGB I2C 12-LLGA
NCP5623B
ILED + IREF @ k (eq. 1)
@ 2400
ILED + Rset (eq. 2)
DC/DC OPERATION
The converter is based on a charge pump technique to
generate a DC voltage capable to supply the RGB LED load.
The system regulates the current flowing into each LED, not
the DC Vout value, by means of internal current mirrors
associated with the diodes.
Consequently, Vout = Vbat * Mode, with Mode = 1 or
Mode = 2, the extra voltage Vout ? Vf being sustained by the
current mirror structure.
The average forward current of each LED can be
independently programmed (by means of the associated
PWM ) to achieve the RGB function. The maximum LED
current, setup by the external current setting resistor
connected across IREF pin and Ground, is associated to the
digital content of the I 2 C register (see Table 1). This peak
current applies to the three LED simultaneously, but, thanks
to the RGB function, the average output current of each LED
is controlled by the independent PWM controllers.
Consequently, the luminosity of each RGB diode can be
independently adjusted to cope with a given illumination
need. Since the peak current is constant, the color of the
RGB diodes is the one defined by the specifications of each
individual LED.
The built ? in OVP circuit continuously monitors the V out
voltage and stops the converter when the voltage is above
5.7 V. The converter resumes to normal operation when the
voltage drops below 4.4 V (no latch ? up mechanism).
Consequently, the chip can operate under no load conditions
during any test procedures.
LOAD CURRENT CALCULATION
The load current is derived from the 600 mV reference
voltage provided by the internal Band Gap associated to the
external resistor connected across I REF pin and Ground.
Note : due to the internal structure of this pin, no voltage,
either downward or upward, shall be forced at the I REF pin.
The reference current is multiplied by the constant
k = 2400 to yield the output load current. Since the reference
voltage is based on a temperature compensated Band Gap,
a tight tolerance resistor will provide a very accurate load
current. The resistor is calculated from the Ohm’s law (R set
= Vref/I REF ) and a more practical equation can be arranged
to define the resistor value for a given maximum output
current:
R set = (Vref*k)/Iout [ 1 ]
R set = (0.6*2400)/Iout
R set = 1440/Iout [ 2 ]
Since the Iref to ILED ratio is very high, it is strongly
optimize the tolerance of the output current. Although it is
possible to use higher or lower value, as defined in the
analog section, a 48 k W / 1% resistor will provide the best
compromise, the dimming being performed by the
appropriate PWM registers.
On the other hand, care must be observed to avoid leakage
current flowing into either the IREF pin or the current setting
resistor.
Finally, for any desired ILED current, the curve provided
Figure 4 can be recalculated according to the equation:
31 * n
Vref
31 * n
with: n = step value @ 1 ≤ n ≤ 30
with: Rset = Current setting resistor
with: k = internal multiplier constant = 2400
Note: n = 0 forces ILED to zero
with: n = 30 and n = 31 yields the same LED current
LOAD CONNECTION
The primary function of the NCP5623B is to control three
LED arranged in the RGB color structure (reference
OSRAM LATB G66x). The brightness of each LED is
independently controlled by a set of dedicated PWM
structure embedded into the silicon chip. The peak current,
identical for each LED, is programmable by means of the
I 2 C data byte. With 32 steps per PWM, the chip provides
32768 colors hue in a standard display.
Moreover, a built ? in gradual dimming provides a smooth
brightness transition for any current level, in both Upward
and Downward direction. The dimming function is
controlled by the I 2 C interface: see Table 2.
The NCP5623B chip is capable to drive the three LED
simultaneously, as depicted in Figure 1, but the load can be
arranged to accommodate several LED if necessary in the
application. Finally, the three current mirrors can be
connected in parallel to drive a single powerful LED, thus
yielding 90 mA current capability in a single LED.
I 2 C PROTOCOL
The NCP5623B is programmed by means of the standard
I 2 C protocol controlled by an external MCU. The
communication takes place with two serial bytes sharing the
same I 2 C frame:
? Byte#1 3 physical I 2 C address
? Byte#2 3 Selected internal registers & function
recommended to set up the reference current at 12.5 m A to
http://onsemi.com
7
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
NCP5623CMUTBG
IC LED DRIVER RGB I2C 12-LLGA
NCP5680MUTXG
IC LED DRIVER WHT HI EFF 24-UQFN
NCP5890MUTXG
IC LED DRVR WHITE BCKLGT 16-UQFN
NCP5901BMNTBG
IC MOSFET DVR SYNC VR12 8-DFN
NCP5901MNTBG
IC MOSFET DVR SYNC VR12 8-DFN
NCP5911MNTBG
IC MOSFET DVR SYNC VR12 8-DFN
NCP692MN50T2GEVB
EVAL BOARD FOR NCP692MN50T2G
NCV7513AFTR2G
IC PREDRIVER HEX LOW SIDE 32LQFP
相关代理商/技术参数
NCP5623C
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Triple Output I2C Controlled RGB LED Driver
NCP5623CMUTBG
功能描述:LED照明驱动器 RGB LED DRIVER W/I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5623DTBR2G
功能描述:LED照明驱动器 RGB LED DRIVER W/I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5623MUTBG
功能描述:IC LED DRIVER RGB 12-LLGA RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT
NCP562-SKT
制造商:ON Semiconductor 功能描述:80 mA CMOS Low Iq Low-Dropout Voltage Regulator 制造商:P&S 功能描述:80 mA CMOS Low Iq Low-Dropout Voltage Regulator
NCP562SQ15T1
功能描述:低压差稳压器 - LDO 1.5V 80mA CMOS RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
NCP562SQ15T1G
功能描述:低压差稳压器 - LDO 1.5V 80mA CMOS w/Enable RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
NCP562SQ18T1
功能描述:低压差稳压器 - LDO 1.8V 80mA CMOS RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20